As described

Questo prodotto è famoso nel mondo della stampa 3d e quindi uno dovrebbe andare a colpo sicuro e invece no! Prima di tutto made in USA ho i miei dubbi ,secondo me è made in cina come sempre. Diciamo che si presenta veramente bene, privo di graffi e privo di sbavature, ma le cose positive finiscono qui, come al solito questi estrusori "all metal" si intasano e non c'è verso di stapparlo senza smontarlo e perdendo tempo, tanto tempo. Altra cosa come detto da altri utenti questo estrusore soffre di perdite come si vede dalle foto. Anche l'estrusione non è nulla di che (foto) ho provato i soliti materiali, pla, petg e asa e i risultati sono in foto. Quindi mi spiace ma lo sconsiglio a 80 euro è veramente una truffa, se lo trovate a 20 euro vi dico prendetelo ma a 80 non esiste. Ma come è possibile che non esista un estrusore decente per una delle macchine più diffuse al mondo ? Ah!! dimenticavo, siccome il grano che blocca l'heatbreak non riesce a sopportare lo sforzo durante una stampa si è levato tutto il blocco riscaldante andando a danneggiare seriamente il letto di stampa (foto) e poi rischiavo di far sviluppare un'incendio in quanto stavo stampando in camera chiusa (stampando asa). Bho! non so cosa dire.

Here I will attempt to give my Experiences an Impressions of the MicroSwiss Hot End!.First I was a bit surprised its called Micro Swiss but its made here in the U.S.?????But We Live In The times We Live In Right!.First off I must say it is a Very Good Unit for as a young fella i had toolshop training and i have to sayin quality the Unit i received was first rate .Now I received My Order quickly so as usual both Amazon and the Seller has their act together and i can only say 'Good Going' guys on the shipping, You did well!...TO INSTALL:I wont go into 'Great Detail' here as their are YouTube videos that explain the detail better then i can.Put simply if you have simple tools most Americans have, And you are capable say of fixing a Kitchen Faucet then you should be able to assemble and mount a MicroSwiss Hot End to a Ender Printer ,.'Now This Is A Balancing Act as Its Important to understand the Pluses and Minuses!'...See My problem was My Bodwin tube melted and started causing my hot end to leak!!!!!.Granted I couldn't see re-placing this with a factory unit, So i bought a MicroSwiss and a newHigh Temp tube!.....So if you are buying this to replace a Bad or Worn or a Defective Hot End then this is a deal for you!...But if you ARE buying this just to increase temps so you can process NYLON or Hi Temp materialsthen 'This Part' alone cannot help you!.In fact it was a 'Bad Disappointment' to find despite adds to the contrary!...Yes and truly Micro Swiss is a top grade part and is an improvement over the factory Hot End!.And i definitely like the way my parts are coming out now, But in truth it only adds about 5 degrees to my operating temperatures!.This Part Does NOT Automatically of itself INSURE that 'Your Machine' will run NYLON!.In Truth Its Kinda A Half and Half Thing!.Most Folks are buying this or something 'like it' for 'Ender Printers' to increase Melt temperatures!.But due to Computer Settings and P.I.D. Enders are 'Locked Down' to 260C O.K.Plus the Heat Block on the Micro Swiss is plain Aluminum and not the Stainless Steel I was hoping for.As that alone "drastically" limits Operating Temperature.Please remember THIS is not a fault, It is simply the way that part is designed to run/operate!.Very Fortunately I Dont have to run Nylon in my normal work!.Yes if i changed the 'Junk Aluminum' block with a Copper Block which Amazon carries that could possibly kick me up towards 270C which would make it more realistic to run some of the newer Nylons that Amazon is currently listing and those are Quality Goods!.Now with a 'Stock Hot End' I ran 'Taulmans 230' which is a low temp NYLON and it turns out some fine parts that has to be said, But i must also point out its not Rock Hard but its good for use where toughness is needed but some flexibility is allowed,.To Close let me state that the MiscroSwiss is good and a fine choice to replace worn and bad parts as it certainly does a fine job in the normal temp range the Machines. were originally designed for!.But clearly DONT buy an ENDER if you intend to run NYLON as that machine simply isnt set up for it!.Yes some people try altering PID or tampering with the computer code and have wound up damaging their machines.Buy a Prusa or a different make which is more Modern and Up to Spec!.But for my uses MicroSwiss makes a fine part, it installed easy, Runs fine and does its Job!.Recommended!IndianaED

Worked like a dream.Before installation I was getting a number of blockages in the hotend due to heat creep and couldn't get rid of it no matter how much a mucked around with the slicer and wasted half a role of filament attempting to dail it in.Bought this and it was essentially plug and play and with a bit of PID test and tweeking, it worked brilliantly

Llevo ya bastantes meses con este hotend en mi Ender 5 PRO. Me encantan porque no he tenido ni un atasco, parece increible pero es así. He imprimido PLA, PETG y FLEX sin ningún tipo de problema, eso si la impresora está modificada para imprimir con extrusión directa.Puedo compararlo con el V6 porque tengo una Prusa MK3S. La boquilla se cambia mucho más fácil que en un V6 que lo tienes que desmontar solo para cambiar una boquilla.Una de las cosas que más me gustan es que al tener la pieza que separa el disipador del bloque calentador de titanio no deja pasar nada la calor por lo que impide que tengas atascos. La verdad, es una pasada, totalmente recomendado.

Non volevo assolutamente spendere così tanto per una hot endHo acquistato tre cloni low costNonostante varie modifiche, prove di settaggi infiniti e un’enorme perdita di tempo, questi cloni non hanno mai funzionatoIl problema era l’intasamento e la continua variazione della portata (flow) anche cambiando vari ugelliQuesto della swiss è perfettoMigliorata la stampa, flow costanteRiesco a stampare pet senza fondere il teflonMontato su CR-10S4 con modifica ad estrusore direttoConsigliato

Super produit maintenant je peux imprimer à l'aise l'abs. Cr10 d'origine monte à 260 c'est parfait. Avant le ptfe cramais et ca bloquait le filament.je recommande.

ottimo prodotto, ora posso stampare il petg senza intoppi, anche aumentando la velocità rispetto allo stock su cr10