Buena calidad. Facil de adaptar lijando hasta conseguir la medida. Blando. Para Squier Stratocaster es perfecta. Solo lijar un poco la longitud y el terón inferior para q baje a su sitio. Hacerlo poco a poco y probando para no pasaros y q quede hueco

perfetta su fender mex

Fini la corde qui accroche au sillet et les désaccordages intempestifs ! Avec ce sillet on retrouve une stabilité d’accordage parfaite et on peut enfin utiliser le vibrato de sa Stratocaster sans craindre le désaccordage (surtout avec des mecas a blocage)

The hardest part was getting my original nut off since it was lacquered in by Fender. I bought my first Tusq XL at Guitar Center and shaved it down too far on the bottom so that I got a little buzz on the low E and G string, oddly enough. So I bought another here on Amazon. You can have it on in under an hour easily if your other nut is already off. Basically, had to shave a little off the back to fit in the slot and then shaved less this time off the bottom, after sanding down the tab they put on there. Didn't mess with the slots at all. My Tele plays great. I think it has better tone and clarity than the original bone nut, especially the Low E string, which with the bone sounds dull and thuddy. I do like the look of bone better though. Just be careful not to go too low when sanding on the bottom. I got mine to about .025" on the first fret on the Low E, which also is about .010" when pressing the Low E down on the third fret and measuring the first fret to the string. My action is about 4/64 on all the strings on the 12th and about .006" on the Low E 8th fret with a capo on the first and pressing around the 19th fret. Seems good enough.

Perfetto per la mia Fender Telecaster Player.

Ottimo capotasto dal suono chiaro, aperto armonico e dinamico .Considerevole aumento delle frequenze medie e medio alte ,da provare ! un considerevole cambiamento sonoro rispetto all’osso o a materiali sintetici e per questo, prudentemente, va valutato in base al suono di partenza dello strumento .Non credevo che un componente così piccolo potesse garantire un così tangibile risultato.Si lavora molto bene .sull’autolubrificazione io direi che è meglio continuare a utilizzare o la grafite o grasso al teflon.

Una piccola cosa per un grande risultato.

ottimo capotasto per fender..va un po' lavorato,limato ma alla fine il risultato e' veramente ottimo soprattutto per l'intonazione delle corde sia per il suono della chitarra.

Exactly what my partscaster needed.Nearly perfect fit on flat bottom, got lucky and didn't need to sand down much to match height. You don't need to prep the string contact point, they are good to go if you're using 9's or 10's on your strat.Good sound and smooth tuning - considering also for my MIM Tele.A good buy, also note it's made in Canada.

Habe den Sattel in einer Affinity Tele verbaut. Da diese Tele weder eine gekrümmte Nut für den Sattel noch den typischen Zapfen hat war ich etwas überrascht. Habe den Zapfen abgefeilt und den Sattel, der auch etwas schmaler war dann in die Nut geklebt. Ach ja die Länge musste für die Tele etwas gekürzt werden. War in wenigen Minuten mit der Feile erledigt. Das Resulat war für Preis und Aufwand richtig gut. Kein Festhängen mehr beim Stimmen und ich musste weder bez. Saitenlage und Bundreinheit etwas anpassen.Das Entfernen des Altsattels hat ca 30 Minuten und das Anpassen bzw. kleben des Neuen ca. 10 Minuten gedauert. Das war mein erster Sattel aus diesem Material, einen Unterschied zum Knochen konnte ich vom Ergebnis her nicht ausmachen. Klare Kaufempfehlung.